How I Buy Router Bits and Workshop Tools: A 6-Step Procurement Checklist
-
Step 1: Write down what the tool is actually for, not what it's called
-
Step 2: Divide the router bit set price by usable pieces
-
Step 3: Don't agonize over the cheap categories
-
Step 4: Convert everything to a monthly replacement cost
-
Step 5: Budget for the consumables separately
-
Step 6: Confirm delivery and invoice terms in writing before you order
-
A few things worth knowing before you start
I manage purchasing for a company with a small workshop attached—about $200K a year total, spread across a dozen or so vendors. Router bits, abrasives, hand tools, the occasional edge case like a mower blade sharpener. This checklist is what I run through before I place a workshop order. It's not exhaustive and it won't make you a machinist. But it saves me from most of the mistakes I used to make.
Six steps. Each one takes maybe two minutes. Skip them and you'll feel it later—I did, more than once.
Step 1: Write down what the tool is actually for, not what it's called
The catalog says "V-groove router bit." Great. What's it cutting, and how deep?
A freud v groove router bit is used for signmaking, decorative edges, and some joinery—the angle matters because a 90° bit isn't interchangeable with a 60° one. Shank diameter matters too: 1/4-inch versus 1/2-inch. Get that wrong and you're either returning the bit or, worse, running it in a collet that doesn't hold it well.
I'm not a woodworker, so I can't speak to edge geometry or rpm optimization—that's the shop's call. What I can do is make sure the order form has machine model, shank size, and max rpm on it. Boring, I know. But I've had to re-order bits because I took someone's verbal description as a spec.
Step 2: Divide the router bit set price by usable pieces
Freud router bits come single or in sets. The set price looks scary at first glance. Divide it by the number of pieces and it's often half the per-piece cost. The catch: only if you'll actually use most of them.
My rule—list the profiles the shop expects to run over the next six to nine months. If a 10-piece router bit set covers five of those profiles, do the math on the unused five and see if the savings justify eating the difference. Sometimes it does, sometimes it doesn't. A set that sits in a drawer is not a bargain.
Also check the bearings. Some sets include them, some don't. If your template work relies on bearing-guided cuts, a set with no bearings is a hidden cost.
Step 3: Don't agonize over the cheap categories
Not every line item deserves a research project.
A mechanics pliers set is a good example. Buy a reputable brand, keep the invoice, move on. We bought one for the shop in 2022—roughly $40 if I remember correctly—and it's still in service. If it breaks, it's $40 and a phone call. There's no TCO debate worth having at that price.
Router bits and saw blades are different. Cheap bits dull fast, burn on harder stock, or leave a rougher cut than the shop wants. That shows up as rework, wasted expensive material, and—ten times out of ten—a conversation with me about why the job is running late. The savings evaporate the first time a $20 bit costs you a $90 piece of stock.
Step 4: Convert everything to a monthly replacement cost
This is where total cost thinking earns its keep. Unit price alone tells you almost nothing about what you'll spend.
Say one bit lasts six months at $40 and another lasts three months at $20. On paper the second is cheaper. In practice it's roughly the same monthly cost—plus the labor to swap it, plus the risk of a dull tool ruining a cut. What I track is unit price divided by expected life, plus downtime. Anything with a low unit price but a high replacement rate goes on the "premium worth paying for" list.
I keep a simple spreadsheet: item, unit price, expected life, replacement frequency. It's not sophisticated. It has saved me from at least two bad orders.
Step 5: Budget for the consumables separately
The tool is half the picture. The grinding wheels, the spare bearings, the sharpening service—those don't show up on the bit invoice, but they're real money.
Example: someone on the grounds team once submitted a request to sharpen the mower blades, which turned into a question about "what grit grinding wheel to sharpen mower blades." I googled it—the answers ranged from 120 down to 200 depending on who was writing. The shop ended up specifying 150 grit for the material they were working with. Fine. But that was a 15-minute detour I didn't expect, and it took two order cycles before the right wheels were on the shelf.
Now I ask the shop to write the specific grit, size, and material on the request. Vague requests waste everyone's time. Consumables get their own line item so they don't quietly eat into the tool allocation.
Step 6: Confirm delivery and invoice terms in writing before you order
This is the step I skipped once and it cost me.
The vendor had quoted 7 days—well, 7 business days, which I'd mentally translated to a calendar week. I knew I should have sent an email to confirm, but I thought, "what are the odds it slips?" Well, the odds caught up with me when the order arrived 15 days later and the job was already behind.
Now I confirm three things in writing before every workshop order: ship date, return policy, and invoice format. If a vendor can't produce a proper invoice—meaning not a handwritten receipt—I walk away. Finance has rejected expenses before over that, and the last thing I need is the purchasing line eating the cost.
A few things worth knowing before you start
- Catalog prices and negotiated prices are not the same number. Don't budget off the list price.
- "Set" does not automatically mean "cheaper per bit." Run the math (see step 2).
- If something's urgent and cheap, buy locally rather than waiting on shipping. The premium is often less than the downtime.
- Keep a record of where each tool came from. Returns are painful without the original seller reference.
None of this is complicated. Write down the spec, divide by the life span, get the delivery date in an email. The checklist works for our situation—a mid-size operation with an attached shop and a few consistent suppliers. If you're running a bigger production line or buying under a centralized contract, the trade-offs look different. But the core logic holds: the lowest per-unit price usually isn't the lowest total cost.